Posted on

3D Printed Vase in 4 colors

IT-Works 3D printed this Twisted 6 sided vase with our E3D Titan Aero 1.75mm toolhead for LulzBot Taz in 4 colors of PLA spliced with the Mosaic Manufacturing Palette+ @PalettePrinted

Posted on

New E3D VOLCANO Titan Aero toolhead for TAZ

MAKE STRONG PRINTS FAST WITH YOUR LulzBot® Taz 3D PRINTER!

The newly released www.itworks3d.com E3D Titan Aero Volcano toolhead for Taz features a 1.2mm nozzle that allows tall layer heights and wide line widths that boost print speed to 80-100 grams per hour or more. This toolhead is compatible with Taz 5 and Taz 6 using the profiles and firmware LulzBot® developed and shared (Thank you!) for their MOARSTRUDER toolhead.
Our toolhead featured the E3D Titan Aero extruder, which features a short, controlled filament path for accurate extrusion, and employs our surround filament cooling duct for improved print cooling performance and quality. Special launch sale price of only $349. Regularly $389

9″ / 225mm tall 200 gram vase printed in 2 hours with the IT-Works E3D Voalcano TItan Aero toolhead for Taz Design is Benito Sanducci’s Gosper Fractal Vase design

Available in for either 3mm or 1.75mm filament!

Compatible with the full range of E3D Volcano nozzles, including wear resistant hardened steel, and high temperature coated copper

Posted on

Deals NOW from IT-Works 3D

IT-Works 3D has released our Black Friday Deals now!

Special limited quantity E3D Titan Aero Toolhead for LulBot Taz $229
E3D Titan Aero Ultralight Toolhead for Taz $249
E3D Titan Aero Toolhead for LulzBot Mini $249
Closeout- Refurbished Toolhead for LulzBot Mini $75
Chroma Strand Labs Inova-1800 co-polyester as low as $39!
Chroma Strand Labs Inova-2008 PETg $34.99
Chroma Strand Labs Premium ABS $34.99
Genuine E3D V6 Extra Nozzles, 3mm and 1.75mm, .4mm size $6.99
40mm x 40mm x 10mm 24V fans only $3.99

Free shipping on all Chroma Strand Labs Filament
Free shipping on orders over $150

Posted on

Better 3D Printer Filament Cooling Duct Improves Print Quality

While printing filament cooling ducts for our E3D Titan Aero toolheads, I noticed that some ducts had consistently poorer print quality on the overhangs of some corners, while others had even performance on all corner overhangs, even when printing with the same printer and filament roll.  Keith pointed out that I had switched toolheads between stock and one of our upgraded E3D Titan Aero toolheads with the surround filament cooling ducts.  I hadn’t expected the more even cooling to make that much of a difference, but it indeed does.

Posted on

Turquoise Vase 3D Print

This beautiful vase was 3D printed in Translucent Turquoise 3mm Chroma Strand Labs Inova-1800 co-polyester filament from Benito Sanducci’s Gosper Fractal Vase design.
Sale? Yes! Turquoise and Turquoise 2 (a darker “emerald” color) Inova-1800 3mm 3D printer filament are a special limited edition on sale for only $39/kg!

Posted on

Maintenance items on the Mini and Taz

To keep your LulzBot Mini and Taz performing at their best, it’s important to check for wear and loose parts periodically.
A few items you can check quickly and easily:

Loose bed mount screws
If you can spin any of the washers that hold down the corners of the bed on the TAZ 6 and Mini, they are too loose. Snug them up with a 2mm hex wrench
No “hulk hands” here though, be careful not to strip out the hole.

Play in the bed plate
Try to wiggle the bed in all directions checking for excessive play that may be caused by loose screws or worn bearings.

If you find more play than you’d expect, it may just be loose screws that secure the bed plate to the double bearing holders. Using a 2mm hex wrench, remove the screws that secure the heat bed washers. Being careful not to lose the screws washers, or spacers below the washers, remove the screws and washers, lift up the heat bed and set it off to the side, and check that the screws underneath the heat bed that secure the bed plate are all snug.

Check play again. If you’ve taken out the play, great! If not, it’s probably time to replace the bearings under the bed plate in the double bearing holders

Play in the X carriage
Wiggle the tool head in all directions to check for excessive play that may be caused by loose screws or worn bearings.

Culprits for play include looseness in the screw/s that secure the toolhead to the X carriage

Loose screws that secure the extruder and hotend to the toolhead mount, cracks in the extruder body and toolhead mount, and worn bearings in the X carriage and x carriage upper bearing holder.

Squeaky smooth rods
Wipe down the smooth rods with a lint free cloth to remove dust and residue. This will often remedy squeaks when the carriages are moving.

If you need to replace worn bearings, the old bearings need to be pressed out, and new bearings pressed in, which can be a bit of a challenge without the right tools.
We have factory made parts for the 1.03 “Foxglove” Mini that include the bearings and heat inserts already installed, so you can conveniently replace the entire bearings housing assembly instead!
All our Mini parts are conveniently organized with pictures here: https://itworks3d.com/product-category/parts/mini-parts/
Here are the parts that contain the bearings that you may want to replace:

x carriage